 |
| |
See our accessory page for high temperature wire and connectors.
Return to Mica Band Heater Configuration Page here.  |
|
Low Profile Terminals
Low profile terminals are available on all mica heaters with post terminals. Call for details.
|
|
|
3 Phase or Dual Voltage
Available on most mica band heaters with leads or post terminals. Some restrictions, such as minimum size, do exist. Please contact Thermal for further information.
|
|
|
Mounting Flange
Available with leads or post terminals. Available on one or two piece band heaters.
|
|
|
Ground Terminals or Ground Wire
May be added to most configurations.
|
|
|
Non-Standard Location of Leads or Terminals
Leads or terminals may be located at any reasonable place along the band heater for applications where standard connections may be inaccessible. Please contact Thermal for details.
|
|
|
Extra Wide Gap
Available on most mica band heaters as a less expensive alternative to holes for thermocouple probe access. Some restrictions apply for heaters with mounting flanges. (Standard gap is 5/16"). Please specify "G" dimension when ordering.
|
|
|
Stainless Steel Sheath
For food processing applications, stainless steel construction is available. Diameters must be 5" or greater for this option. |
|
|
Holes or Notches
Any reasonable size and location is available on custom designed mica band heaters. Please contact Thermal for assistance in determining feasibility. |
 --  |
|
Low Profile Strap
Low profile strap is standard for band heaters with ID's of 3" or less and widths of 2" or less. available on request for larger nozzle bands. |
|
|
Standard Clamping Strap
All mica band heaters over 3" wide will automatically be furnished with more than one strap. Call Thermal for details if additional straps are required. |
|
|
Spring Strain Relief
Strain relief spring that goes over stainless steel overbraid (approximately 4" coverage from where leads exit band heater) available on config. 417, 516, 517, 518, 519, 536, 546, 547 and strip heater config. 016. |
|
|
Copper Elbow with Stainless Steel Hose
3/8" flexible hose soldered to elbow available on band heater configurations 415, 514, 520, 521, 538, 544, and 545 and strip heater conf. 014. Please specify orientation of elbow to heater when ordering. |
|
|
Copper Elbow with Stainless Steel Overbraid
Available on most heaters with leads. Some restrictions, such as minimum size, do exist. Please contact Thermal for further information. |
|
|
Incorporated Strap
Clamping strap is built-in as integral part of the band heater. |
|
|
Clamp Strap with Pads
Used with partial band heaters when straps are attached to barrel. |
|
|
Strap with Spring Clamp
Recommended for larger diameter applications (above 10" ID) to insure adequate clamping actions. |
|
|
Bayonet Adapter Attached to Heater
A standard bayonet adapter is soldered to a bracket then attached to the heater above a 3/8" diameter hole. Please specify adapter size when ordering. |
|
|
Terminal Box
Available for most configurations that have post terminals side by side. 1 piece heater 3" ID, 3" width; 2 - piece heaters 3" width |
|
|
Terminal Box Attached to Strap
Available on most configurations with in-line post terminals. 1 piece heater 3-1/2" ID, 1-1/4" width; 2 piece heater 5" ID, 1-14" width |
|
|
3 Phase and Dual Voltage T-Boxes
Available on most configuration that have post terminals side by side. One-piece heater - 3" ID, 3" width; two-piece heater - 3" widths. |
|
|
European Connector
2-pole cup type European plug available on most configurations. Some restrictions, such as minimum diameter and minimum width do exist. Please contact Thermal Corp for further assistance. |
|
Updated
March 13, 2007
.
|
